DTS6503品牌授权规格书.pdf

《DTS6503品牌授权规格书.pdf》由会员分享，可在线阅读，更多相关《DTS6503品牌授权规格书.pdf（10页珍藏版）》请在得力文库 - 分享文档赚钱的网站上搜索。

1、1P-Channel 30-V(D-S)MOSFETFEATURESHalogen-free According to IEC 61249-2-21AvailableTrenchFET Power MOSFETAPPLICATIONSLoad SwitchPRODUCT SUMMARY VDS(V)RDS(on)()ID(A)aQg(Typ.)-300.053 at VGS=-10 V-5.15.1 nC0.066 at VGS=-4.5 V-4.1Notes:a.Based on TC=25 C.b.Surface Mounted on 1 x 1 FR4 board.c.t=5 s.d.M

2、aximum under Steady State conditions is 110 C/W.ABSOLUTE MAXIMUM RATINGS TA=25 C,unless otherwise notedParameterSymbol Limit UnitDrain-Source Voltage VDS-30VGate-Source Voltage VGS 20Continuous Drain Current(TJ=150 C)TC=25 CID-5.1ATC=70 C-4.1TA=25 C-4.1b,cTA=70 C-3.3b,cPulsed Drain CurrentIDM-20Cont

3、inuous Source-Drain Diode Current TC=25 CIS-2.5TA=25 C-1.67b,cMaximum Power DissipationTC=25 CPD3.0WTC=70 C2.0TA=25 C2.0b,cTA=70 C1.3b,cOperating Junction and Storage Temperature Range TJ,Tstg-55 to 150CTHERMAL RESISTANCE RATINGS ParameterSymbolTypicalMaximumUnitMaximum Junction-to-Ambientb,dt 5 sRt

4、hJA5562.5C/WMaximum Junction-to-Foot(Drain)Steady StateRthJF3441TSOP-6Top View6412352.85 mm3 mm(4)S(3)G(1,2,5,6)DP-Channel MOSFET DTS65032Notes:a.Pulse test;pulse width 300 s,duty cycle 2%b.Guaranteed by design,not subject to production testing.Stresses beyond those listed under“Absolute Maximum Rat

5、ings”may cause permanent damage to the device.These are stress ratings only,and functional operationof the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied.Exposure to absolute maximumrating conditions for extended period

6、s may affect device reliability.SPECIFICATIONS TJ=25 C,unless otherwise notedParameterSymbol Test Conditions Min.Typ.Max.UnitStaticDrain-Source Breakdown VoltageVDS VGS=0 V,ID=-250 A-30VVDS Temperature CoefficientVDS/TJID=-250 A-31mV/CVGS(th)Temperature CoefficientVGS(th)/TJ4.5Gate-Source Threshold

7、VoltageVGS(th)VDS=VGS,ID=-250 A-1.0-3.0VGate-Source LeakageIGSSVDS=0 V,VGS=20 V 100nAZero Gate Voltage Drain CurrentIDSSVDS=-30 V,VGS=0 V-1AVDS=-30 V,VGS=0 V,TJ=55 C-10On-State Drain CurrentaID(on)VDS -5 V,VGS=-10 V-20ADrain-Source On-State ResistanceaRDS(on)VGS=-10 V,ID=-4.1 A 0.0400.053VGS=-4.5 V,

8、ID=-1.0 A 0.0520.066Forward TransconductanceagfsVDS=-15 V,ID=-4.1 A 8SDynamicbInput CapacitanceCiss VDS=-15 V,VGS=0 V,f=1 MHz450pFOutput CapacitanceCoss 80Reverse Transfer CapacitanceCrss 63Total Gate ChargeQg VDS=-15 V,VGS=-10 V,ID=-4.1 A1015nCVDS=-15 V,VGS=-4.5 V,ID=-4.1 A5.18Gate-Source ChargeQgs

9、 1.8Gate-Drain ChargeQgd2.5Gate ResistanceRgf=1 MHz7Turn-On Delay Timetd(on)VDD=-15 V,RL=4.6 ID -3.3 A,VGEN=-4.5 V,Rg=1 4060nsRise Timetr 80120Turn-Off Delay Timetd(off)2030Fall Timetf1220Turn-On Delay Timetd(on)VDD=-15 V,RL=4.6 ID -3.3 A,VGEN=-10 V,Rg=1 510Rise Timetr 1320Turn-Off Delay Timetd(off)

10、2030Fall Timetf1015Drain-Source Body Diode CharacteristicsContinuous Source-Drain Diode CurrentISTC=25 C-2.5APulse Diode Forward CurrentaISM-20Body Diode VoltageVSDIS=-3.3 A-0.8-1.2VBody Diode Reverse Recovery TimetrrIF=-3.3 A,di/dt=100 A/s,TJ=25 C2030nsBody Diode Reverse Recovery ChargeQrr2030nCRev

11、erse Recovery Fall Timeta14nsReverse Recovery Rise Timetb6 DTS65033TYPICAL CHARACTERISTICS 25 C,unless otherwise noted Output CharacteristicsOn-Resistance vs.Drain Current and Gate VoltageGate Charge0481216200.00.51.01.52.02.53.0VDS-Drain-to-Source Voltage(V)ID-Drain Current(A)VGS=10 thru 5 VVGS=3 V

12、VGS=4 VVGS=2 V0.000.040.080.120.160.20048121620-On-Resistance()RDS(on)ID-Drain Current(A)VGS=10 VVGS=4.5 V0246810024681012ID=4.1 A-Gate-to-Source Voltage(V)Qg-Total Gate Charge(nC)VGSVDS=24 VVDS=15 VTransfer CharacteristicsCapacitanceOn-Resistance vs.Junction Temperature01234501234 VGS-Gate-to-Sourc

13、e Voltage(V)ID-Drain Current(A)TC=125 CTC=25 CTC=-55 CCrss0200400600800051015202530CissVDS-Drain-to-Source Voltage(V)C-Capacitance(pF)Coss0.60.81.01.21.41.6-50-250255075100125150TJ-Junction Temperature(C)(Normalized)-On-ResistanceRDS(on)VGS=10 V,ID=4.1 VVGS=4.5 V,ID=4.1 A DTS65034TYPICAL CHARACTERIS

14、TICS 25 C,unless otherwise noted Source-Drain Diode Forward VoltageThreshold Voltage00.20.40.60.81.01.2 1.4TJ=150 C10VSD-Source-to-Drain Voltage(V)IS-Source Current(A)1100TJ=25 C1.21.41.61.82.02.2-50-250255075100125150ID=250 A V (V)GS(th)TJ-Temperature(C)On-Resistance vs.Gate-to-Source VoltageSingle

15、 Pulse Power 0.000.050.100.150.200.250246810-On-Resistance()RDS(on)VGS-Gate-to-Source Voltage(V)TJ=25 CTJ=125 CID=4.1 A0510152025Power(W)Time(s)1010000.10.010.0011001Safe Operating AreaVDS-Drain-to-Source Voltage(V)*VGS minimum VGS at which RDS(on)is specified10010.11101000.0110ID-Drain Current(A)0.

16、1TA=25 CSingle Pulse1 ms10 msLimited by RDS(on)*BVDSSLimited100 s100 msDC1s,10 s DTS65035TYPICAL CHARACTERISTICS 25 C,unless otherwise noted *The power dissipation PD is based on TJ(max)=150 C,using junction-to-case thermal resistance,and is more useful in settling the upperdissipation limit for cas

17、es where additional heatsinking is used.It is used to determine the current rating,when this rating falls below the packagelimit.Current Derating*0123450255075100125150TC-Case Temperature(C)6ID-Drain Current(A)Power,Junction-to-Foot01234255075100125150TC-Case Temperature(C)Power(W)DTS65036TYPICAL CH

18、ARACTERISTICS 25 C,unless otherwise noted Normalized Thermal Transient Impedance,Junction-to-Ambient10-310-2110100010-110-41000.20.10.05Square Wave Pulse Duration(s)Normalized Effective TransientThermal Impedance10.10.01t1t2Notes:PDM1.Duty Cycle,D=2.Per Unit Base=RthJA=90 C/W3.TJM-TA=PDMZthJA(t)t1t2

19、4.Surface MountedDuty Cycle=0.50.02Single PulseNormalized Thermal Transient Impedance,Junction-to-Foot10-310-201110-110-40.20.1Duty Cycle=0.5Square Wave Pulse Duration(s)Normalized Effective TransientThermal Impedance10.10.01Single Pulse0.020.05 DTS650311 2 3 Gauge Plane L 5 4 R R C 0.15 M B A b C 0

20、.08 0.17 Ref Seating Plane-C-Seating Plane A 1 A 2 A-A-D-B-E 1 E L 2(L 1)c 4x 1 4x 1 e e1 1 2 3 6 5 4 C 0.15 M B A b-B-E 1 E e e1 5-LEAD TSOP 6-LEAD TSOP TSOP:5/6LEADJEDEC Part Number:MO-193CMILLIMETERS INCHES Dim Min Nom Max Min Nom Max A 0.91-1.10 0.036-0.043 A 10.01-0.10 0.0004-0.004 A 20.90-1.00

21、 0.035 0.038 0.039 b 0.30 0.32 0.45 0.012 0.013 0.018 c 0.10 0.15 0.20 0.004 0.006 0.008 D 2.95 3.05 3.10 0.116 0.120 0.122 E 2.70 2.85 2.98 0.106 0.112 0.117 E 11.55 1.65 1.70 0.061 0.065 0.067 e 0.95 BSC 0.0374 BSC e 11.80 1.90 2.00 0.071 0.075 0.079 L 0.32-0.50 0.012-0.020 L 10.60 Ref 0.024 Ref L

22、 20.25 BSC 0.010 BSC R 0.10-0.004-0 4 8 0 4 8 1 7 Nom 7 Nom ECN:C-06593-Rev.I,18-Dec-06DWG:5540 DTS65031A P P L I C A T I O N N O T ERECOMMENDED MINIMUM PADS FOR TSOP-60.119(3.023)Recommended Minimum PadsDimensions in Inches/(mm)0.099(2.510)0.064(1.626)0.028(0.699)0.039(1.001)0.020(0.508)0.019(0.493

23、)Return to Index DTS65031DisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons acting on its or their behalf(collectively,“Din-T

24、ek”),disclaim any and all liability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products for any particular purpose orthe continuing p

25、roduction of any product.To the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or incidental damages,and(iii)any and all implied warr

26、anties,including warranties of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often placed on Din-Tek products in generic applicatio

27、ns.Such statements are not binding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for use in a particular application.Parameterspr

28、ovided in datasheets and/or specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product specifications do not expand or otherwise m

29、odify Din-Tek s terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any other application in which the failure of t

30、he Din-Tek product could result in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and conditions regarding products designed for such

31、applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Material Category PolicyDin-Tek Intertechnology,Inc.her

32、eby certifies that all its products that are identified as RoHS-Compliant fulfill thedefinitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Councilof June 8,2011 on the restriction of the use of certain hazardous substances in electrical and electronic

33、equipment(EEE)-recast,unless otherwise specified as non-compliant.Please note that some Din-Tek documentation may still make reference to RoHS Directive 2002/95/EC.We confirm thatall the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.Din-Tek Intertechn

34、ology,Inc.hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Freerequirements as per JEDEC JS709A standards.Please note that some Din-Tek documentation may still make referenceto the IEC 61249-2-21 definition.We confirm that all the products identified as being

35、 compliant to IEC 61249-2-21conform to JEDEC JS709A standards.DTS6503DisclaimerALL PRODUCT,PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVERELIABILITY,FUNCTION OR DESIGN OR OTHERWISE.Din-Tek Intertechnology,Inc.,its affiliates,agents,and employees,and all persons actin

36、g on its or their behalf(collectively,“Din-Tek”),disclaim any and all liability for any errors,inaccuracies or incompleteness contained in any datasheet or in any otherdisclosure relating to any product.Din-Tek makes no warranty,representation or guarantee regarding the suitability of the products f

37、or any particular purpose orthe continuing production of any product.To the maximum extent permitted by applicable law,Din-Tek disclaims(i)any and allliability arising out of the application or use of any product,(ii)any and all liability,including without limitation special,consequential or inciden

38、tal damages,and(iii)any and all implied warranties,including warranties of fitness for particularpurpose,non-infringement and merchantability.Statements regarding the suitability of products for certain types of applications are based on Din-Tek s knowledge of typicalrequirements that are often plac

39、ed on Din-Tek products in generic applications.Such statements are not binding statementsabout the suitability of products for a particular application.It is the customer s responsibility to validate that a particularproduct with the properties described in the product specification is suitable for

40、use in a particular application.Parametersprovided in datasheets and/or specifications may vary in different applications and performance may vary over time.Alloperating parameters,including typical parameters,must be validated for each customer application by the customer stechnical experts.Product

41、 specifications do not expand or otherwise modify Din-Tek s terms and conditions of purchase,including but not limited to the warranty expressed therein.Except as expressly indicated in writing,Din-Tek products are not designed for use in medical,life-saving,or life-sustainingapplications or for any

42、 other application in which the failure of the Din-Tek product could result in personal injury or death.Customers using or selling Din-Tek products not expressly indicated for use in such applications do so at their own risk.Pleasecontact authorized Din-Tek personnel to obtain written terms and cond

43、itions regarding products designed for such applications.No license,express or implied,by estoppel or otherwise,to any intellectual property rights is granted by this document or byany conduct of Din-Tek.Product names and markings noted herein may be trademarks of their respective owners.Legal Disclaimer Notice