Maxim MAX7060 280-450MHz可编程ASK发送方案.docx

《Maxim MAX7060 280-450MHz可编程ASK发送方案.docx》由会员分享，可在线阅读，更多相关《Maxim MAX7060 280-450MHz可编程ASK发送方案.docx（5页珍藏版）》请在得力文库 - 分享文档赚钱的网站上搜索。

1、Maxim MAX7060 280-450MHz可编程ASK发送方案Maxim 公司的MAX7060 是280-450MHz可编程ASK/FSK发送器，采用全集成分数N合成器，起动时间小于25us，50kbps Manchester 数据速率ASK ，70kbps Manchester 数据速率FSK ，5V电源发送功率达14dBm，主要应用在车库门开始，遥控，家庭和工业自动化，传感器网络和安全系统。本文介绍 MAX7060主要特性，方框图，SPI模式和人工模式应用电路图和相应的材料清单。280MHz to 450MHz Programmable ASK/FSK TransmitterThe

2、MAX7060 frequency and power-programmable ASK/FSK transmitter operates at 280MHz to 450MHz frequencies. This device incorporates a fully integrated fractional-N synthesizer, which allows the user to set the RF operating frequency to a large fraction of the 280MHz to 450MHz frequency range with a sing

3、le crystal. For example, the MAX7060 can be tuned from 285MHz to 420MHz with a 15MHz crystal. The RF output power is user-controlled between +14dBm and -14dBm, with a 5V supply or with battery voltages as low as 3.2V. At the minimum specified battery voltage of 2.1V, the RF output power-control rang

4、e is between +10dBm and -14dBm. To maintain a good output power match across a broad range of frequencies, the MAX7060 also contains a programmable matching capacitor connected in parallel with the power amplifier (PA) output.ASK modulation is accomplished by switching the PA on and off, so excellen

5、t modulation (on/off) ratios are achieved. ASK amplitude shaping is available to reduce the width of the transmission spectrum. FSK modulation is accomplished by changing the coefficients of the high-resolution fractional-N synthesizer, so FSK deviation is extremely accurate. Data rates up to 50kbps

6、 Manchester coded for ASK and 70kbps Manchester coded for FSK can be maintained while still satisfying regulatory emission-bandwidth standards. The full set of configuration functions are handled by an on-chip serial peripheral interface (SPIK). There is also a manual mode where a limited number of

7、settings can be made directly through selected pins.The startup time is very short, and data can be transmitted 250Fs after the enable command. The MAX7060 operates from a 2.1V to 3.6V supply, or internal regulators can be used for supply voltages between 4.5V and 5.5V. The standby current in the 3V

8、 mode is 400nA at room temperature, and can be reduced to 5nA using the low-power shutdown (LSHDN) pin.The MAX7060 is available in a 24-pin (4mm x 4mm) thin QFN package and is specified for the automotive temperature range from -40NC to +125NC.MAX7060主要特性：Fully Integrated, Fast Fractional-N PLL 280M

9、Hz to 450MHz RF Frequency Frequency Range 100% Tested at +125degree C 250s Startup Time Adjustable FSK Mark and Space Frequencies Ultra-Clean FSK Modulation 50kbps Manchester Data Rate ASK 70kbps Manchester Data Rate FSKProgrammable Power Amplifier +14dBm Tx Power with 5V Supply +10dBm Tx Power at 2

10、.1V Supply 28dB Power-Control Range in 1dB StepsTunable PA Matching CapacitorControl Through SPI or Manual SettingsLow Shutdown Current for 2.1V to 3.6V Supply 400nA Standby Current, Power-On-Reset (POR) Active 5nA Shutdown Current, POR InactiveSupply Flexibility 2.1V to 3.6V Single-Supply Operation

11、 or 4.5V to 5.5V Supply Operation with Internal Regulators24-Pin (4mm x 4mm) TQFN PackageFCC Part 15, ETSI EN 300 220 CompliantMAX7060应用：Garage-Door OpenersRemote ControlsHome and Industrial AutomationSensor NetworksSecurity Systems图1。MAX7060方框图图2。MAX7060 SPI模式（5V电源）应用电路图SPI模式（5V电源）应用材料清单：图3。MAX7060 人工模式（3V电源，整形ASK调制，315MHz）应用电路图AO-Electronics 傲壹电子 官网： 中文网：ALPS ADI IR JRC/NJR KEC OTAX Seoul Semiconductor TI Walsin Technology人工模式应用材料清单：