插件国巨电阻规格书.pdf

《插件国巨电阻规格书.pdf》由会员分享，可在线阅读，更多相关《插件国巨电阻规格书.pdf（9页珍藏版）》请在得力文库 - 分享文档赚钱的网站上搜索。

1、 Page-1 Approval Sheet for Carbon Film Resistors CFR series 2%&5%YAGEO CORPORATION Headquarters:3F,No.233-1,Pao Chiao Rd.,Shin Tien,Taipei,Taiwan,R.O.C.Tel:886-2-2917-7555 Fax:886-2-2917-4286 URL:.tw Page-2 Page-3 1.PRODUCT:CARBON FILM RESISTORS(Normal&Miniature Style)2.PART NUMBER:Part number of th

2、e carbon film resistor is identified by the name,power,tolerance,packing,temperature coefficient,special type and resistance value.Example：CFR -12 J T J 52 100R Series Size Resistance Packing Temperature Special Resistance Name Code Tolerance Style Coefficient Type Value of Resistance (1)Style:CFR S

3、ERIES (2)Power Rating:-12=1/6W、25S=1/4WS、-25=1/4W、50S=1/2WS、-50=1/2W、1WS=1WS、100=1W、2WS=2WS、200=2W (3)Tolerance:G=2%J=5%(4)Packaging Type:RPaper Taping Reel TTape on Box Packing BBulk Packing (5)T.C.R:J=350ppm/=lgnore (6)Special Type:2626mm、52=52.4mm、73=73mm、PNPANAsert AVAVlsert (7)Resistance Value:

4、1R、10R、100R、10K、100K、330K、1M Page-4 3.BAND-CODE:4.ELECTRICAL CHARACTERISTICS Tabe I *Standard resistance is 1 10M,below or over this resistance on request.*Rated Continuous Working Voltage(RCWV)=Value ResistanceRatingPower FIG.1 TEMPERATURE COEFFICIENT Page-5 5.DERATING CURVE&HOT-SPOT TEMPERATURE 6.

5、DIMENSIONS 7.ENVIRONMENTAL CHARACTERISTICS (1)Short Time Over Load Test At 2.5 times of the rated voltage.(If the voltage exceeds the maximum load voltage,the maximum load voltage will be used as the rated voltage)applied for 5 seconds,the resistor should be free from defects after the resistor is r

6、eleased from load for about 30 minutes and the change of the resistance value should be within(0.25%+0.05)as compared with the value before the test.Page-6 (2)Dielectric Withstanding Voltage The resistor is placed on the metal V Block.Apply a Table I dielectric withstanding between the terminals con

7、nected together with the block for about 60 seconds.The resistor shall be able to withstand without breakdown or flashover.(3)Temperature Coefficient Test Test of resistors above room temperature 125C to 130C(Testing Temperature)at the constant temperature silicon plate for over 4 to 5 minutes.Then

8、measure the resistance.The Temperature Coefficient is calculated by the following equation and its value should be within the range of requested.600010tt1RRRtCoefficieneTemperatursistorRe =R Resistance value under the testing temperature R0 Resistance value at the room temperature t The testing temp

9、erature to Room temperature (4)Insulation Resistance Apply test terminal on lead and resistor body.The test resistance should be high than 10,000 Mohm.(5)Solderability Immerse the specimen into the solder pot at 2305C for 50.5 seconds.At least 95%solder coverage on the termination.(6)Resistance to S

10、olvent The specimen into the appropriate solvent of Methyleme Chloride condition of ultrasonic machine for 1 minutes.The specimen is no deterioration of coatings and color code.(7)Terminal Strength Direct Load Resistors shall be held by one terminal and the load shall be gradually applied in the dir

11、ection of the longitudinal axis of the resistor unit the applied load reacheds 5 pounds.The load shall be held for 10 seconds.The load of weight shall be 2.5kg(24.5N).Page-7 (8)Pulse Overload Apply 4 times of rated voltage to the specimen at the 1 second on and 25 seconds off cycle,subjected to volt

12、age application cycles specified in 10000.The change of the resistance value shall be within(2%+0.05).(9)Load Life in Humidity Place the specimen in a test chamber at 402C and 9095%relative humidity.Apply the rated voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle.The total length o

13、f test is 1000 hours.The change of the resistance value shall be within(1.5%+0.05).(10)Load Life Test Placed in the constant temperature chamber of 703C the resistor shall be connected to the lead wire at the point of 25mm.Length with each terminal,the resistors shall be arranged not much effected m

14、utually by the temperature of the resistors and the excessive ventilation shall not be performed,for 90 minutes on and 30 minutes off under this condition the rated D.C.voltage is applied continuously for 1000+48/-0 hours then left at no-load for 1hour,the change of the resistance value measured at

15、this time to the value before the test shall be within(1.5%+0.05).There shall be no remarkable change in the appearance and the color code shall be legible after the test.(11)Temperature Cycling Test The temperature cycle shown in the following table shall be repeated 5 times consecutively.The measu

16、rement of the resistance value is done before the first cycle and after ending the fifth cycle,leaving in the room temperature for about 1 hour,the change shall be within(1%+0.05).After the test the resistor shall be free from the electrical or mechanical damage.Temperature Cycling Conditions:Step T

17、emperature(C)Time(minute)1+25+10 -5 10 to15 2-65+0 -3 30 3+25+10 -5 10 to15 4+150+3 -0 30 Page-8 (12)Resistance to Soldering Heat The terminal lead shall be dipped into the solder pot at 35010C for 30.5 seconds up to 3 mm.The change of the resistance value shall be within(1%+0.05).8.PACKING METHODS Bandolier for Axial leads The resistors are supplied on bandolier,either 1000 resistors in ammopack or 5000 resistors on reel.9.TAPE ON REEL PACKING&TAPE ON BOX PACKING Page-9 10.SPECIAL TYPE(FORMING DIMENSIONS)