《同异步双模控制系统-用户手册.docx》由会员分享,可在线阅读,更多相关《同异步双模控制系统-用户手册.docx(16页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、HD-D10/D20/D30 Series Asynchronous operate manual1 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedChapter1 SummaryHDPlayer Software we promoting for Full Color door head display. It can remote display by long distance, play high definition video, picture and text etc. It is Asynchronous
2、 model system. The system include two main parts: HD-D10/D20/D30and software.The core part it is controller HD-D10/D20/D30, it is responsible for setting up parameter and sending program. It play program Asynchronous.The controller connected the display, it is responsible for receiving data and send
3、ing the date and showing program on the display1. Hardware structurePart Name Part No FunctionFull color controller HD-D10/D20/D30 Asynchronous controller and store programSoftware HDPlayer Screen set、create program、send programAccessories - Hub、network cable、u disk2. Controller working system1) Clu
4、ster managementNote: The Network cable made by 568B2) Direct managementNote: The Network cable made by 568BHD-D10/D20/D30 Series Asynchronous operate manual2 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedChapter 2 Adjust the display procedureWhen first time use Sending controller HD-D1
5、0/D20/D30, it need use Network cable connect the display. When found the controller ID automatically, then set up the display parameter. Show as belowHD-A60X Series Asynchronous-Synchronous operate manual3 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedChapter 3 Hardware connect1. The C
6、ontroller HD-D10/D20/D30 connect Hub Using the HUB connected with HD-D3, like HUB08 etc2. Network connectedDirect to the pc by the network cable Also can connect with Router, then via Router connected PCNetwork cable use the 568BThe 2 network port can be change of Receiving card4. The power chargerT
7、he power charger voltage it is 4V-5.5V when power on, the “POWER” is bright, “RUN” and “DISPLAY” is flicker.HD-A60X Series Asynchronous-Synchronous operate manual4 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedChapter 4 Network setting The controller HD-D10/D20/D30 series can connect c
8、omputer directly, also can via Router connected computer.When connected with computer, the network port(The Green light always flicker, the green light bright),-then wait for few seconds (Windows XP more than 10Seconds, Window7 less than 10Seconds).-When the right corner of computer show Network nor
9、mal (see below), it means it have been connected of network, -then open the software HDPlayer, it will find the controller ID automatically.orHD-A60X Series Asynchronous-Synchronous operate manual5 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedChapter 5 The Hardware setting 1. Connecti
10、on setting. Setting-Hardware setting- Connection setting1) Select the controller ID2) Receive card parameter: Click Smart setting.First time using this controller HD-D10/D20/D30series, it need Smart setting at first.1). Click Smart setting, then into basic information.2) Click Next, then into Data P
11、olarity settingOne led module pixel of widthClick A, what is the display status of displayClick B, what is the display status of displayResult: A is Black or B is blackHD-A60X Series Asynchronous-Synchronous operate manual6 / 16The rights subject to Shenzhen Huidu Technology Co.,Lted3) Click Next ,
12、then into Data Polarity setting4) Click Next, then into Color channel setting.5) Click Next, then into Line controlled by One RGB DataClick A, what is the display color Click B what is the display color Click C, what is the display color Click D, what is the display color How many lines lighting in
13、display This step for scan type Click A, what is the display status of displayClick B, what is the display status of displayResult: A is Brighter than B Or B is Brighter than AHD-A60X Series Asynchronous-Synchronous operate manual7 / 16The rights subject to Shenzhen Huidu Technology Co.,Lted6) Click
14、 Next, then it into display scan typesLike this led module from right corner of first module (First flicker led from 16th lines of first light)User can use key to move7) The last step, Into Alignment descriptionHow many lines lighting in display This step for scan type (the ways: 16/1=16, so it is 1
15、6 scan )According to the Top Right corner of the first led display module, the bright light flicker (in the first led module), then click this place on the Alignment description HD-A60X Series Asynchronous-Synchronous operate manual8 / 16The rights subject to Shenzhen Huidu Technology Co.,LtedThe la
16、st step display showing 4. Basic parameter1) Refresh rate: The more highly refresh rate, the led display play more fluently. If lower Than 100MHZ, the showing photo shake clearly. The Refresh rate calculate by computer, no need write by hand. 1) Refresh acceleration: It according to Refresh rate and
17、 add it by proportional. For example, the fresh rate 120, the acceleration it is 2; if change to 4,the fresh rate 240MHZ.2) Gray LevelThe Gray Level is used to represent the color richness. More higher more better. Gray level256、512、1024、2048、4096、8192、16384、32768、65536 etc. Usually set 4096 or 8092
18、The gray level is inversely proportional to the longest width of led display The gray level is proportional to luminance efficiency3) Brightness level : Usually Low light, normal and high light.If Alignment successfully, it show like this and saved file.(Next time if have same led display, do not ne
19、ed set again, just click Setting Hardware setting Import, importing this .doo file HD-A60X Series Asynchronous-Synchronous operate manual9 / 16The rights subject to Shenzhen Huidu Technology Co.,Lted5) Frequency: It means the shift frequency of the scan program. Its range 3.125MHz-31.25MHz. it is be
20、tter to set the frequency lower than 25MHz.Because most LED screen driver ICs is lower than 25MHz.4) Priority ModeBrightness Priority: Protecting the brightness lost less, then do refresh acceleration, usually used for outdoor display require high brightness.Refresh Priority: In this mode, it will s
21、acrifice about20% brightness efficiency. It can update Frequency clearly. Usually used for indoor display.Gray level Priority : If for lower brightness requirement, it can select this mode. Usually used for indoor led display.5) Output mode Normal output: For ordinary HUB type.Two separate output: F
22、or sacrifice half control height to increase 1 times control width (Refresh rate and brightness no change)Four separate output: For sacrifice 3/4 control height to increase 4 times control width (Refresh rate and brightness no change)Note: Two separate output and Four separate output can not use tog
23、ether with Extension board6) Gamma: The Gamma represent the contrast degree between light and dark. The higher data the higher contrast. The range 1.0-6.0 and usually set 2.87) Display calibration: For color correction (Red,Green,Blue)8) Use Expansion board: For sacrifice half control height to incr
24、ease 1 times control width (Refresh rate and brightness no change)9) Use20 Groups of RGB: Just used for specified HUB, Like HUB75(20 Height)10) 138 Decoder: According to led module, whether use 138 decoder.11) Data Polarity: Two types of High effective and low effective .If in high effective, the LE
25、Dlight will be lighten up, and shut down with low effective 12) OE Polarity: The OE Polarity with same features as Data Polarity.13) Phase: The relative time relationship between moving clock and moving data. If showing photo have flicker or dislocation, adjust this parameter it can eliminate14) Dut
26、y cycle: The moving clock of duty cycle. If change this data, it can increase thescanning moving clock, usually set 50%15) Blank lines: When refresh rate high, it could result showing afterglow, adjust this data itcan decrease affect, but can not eliminate. It used for scan modules, for static modul
27、e it is uselessHD-A60X Series Asynchronous-Synchronous operate manual10 / 16The rights subject to Shenzhen Huidu Technology Co.,Lted16) Luminance efficiency: The higher and the more brighter, usually set 85%The Chapter 6 Edit programThe software interface have 2 parts: Play window and edit program w
28、indowFor Program window: Click File-New(screen)-Program-Frame-add video, photo etc1. Software interface.1) Play window (the program showing in the display) : User show programvideo, Pictures, Text, etc in the display2) Edit program window: Menu ,Tool ,Structure and attributeEdit program window2. Scr
29、een structureScreen: In first sequence. Decide the play contents in display. Each Screen relationship it is equal. In screen, it can add more ProgramsProgram: In second sequence, and playing By sequenceFrame: In Third sequence, and it can addmore frame in one programMenu TOOL ToolAttributePlay windowgramFramePlay content