小龟直按TVAU07轻触开关.doc

《小龟直按TVAU07轻触开关.doc》由会员分享，可在线阅读，更多相关《小龟直按TVAU07轻触开关.doc（15页珍藏版）》请在得力文库 - 分享文档赚钱的网站上搜索。

1、【精品文档】如有侵权，请联系网站删除，仅供学习与交流小龟直按TVAU07轻触开关.精品文档.客户名称（Customer）: _规 格 承 认 书 SPECIFICATION FOR APPROVALMONTH / DAY / YEAR ISSUED01 / 23 / 07 发行贵公司部品名称： 敝公司部品名称：小龟直按轻触开关 PART NAME SUPPLIERS PART NAME 贵公司部品型号： 敝公司部品型号：TVAU07 PART NUMBER SUPPLIERS PART NUMBER 接受印 兹证明此份材料已经收到。ACKNOWLEDGEMENT WE ACKNOWLEOGE

2、RECEIVING THIS DOCUMENT . MONTH / DAY / YEARDATE: / /GMGRLEADERCHECKEDSIGNED相关规格，规格书 / SPECIFICATIONCHECKED SIGNEDTACT SWITCH SPECIFICATION（轻触开关说明书）1.General specification 基本说明1.1 Scope 范围 This specification covers the requirements for single key switches which have no keytop(TACT SWITCHES:MECHANICA

3、L CONTACT).此规范含盖单推柄和无推柄的轻触开关要求1.2 Operating Temperature Range 使用温度范围 -20 to70(normal humidity, normal press.) 正常湿度，标准压力 1.3 Storage Temperature Range 保存温度范围-30 to80(normal humidity, normal press.) 1.4 Test Conditions 测试条件 Tests and measurements shall be made in the following standard clnditions unle

4、ss otherwise specified: 测试和计量按下列标准条件除非特殊说明 Normal temperature (temperature 5 to 35) 标准温度 Normal humidity (relative humidity 45 to85%) 正常湿气 Normal pressure (pressure 860 to 1060 mbars) 标准压力 In case any question arises from the judgement made, tests shall be conducted in the following conditions: Temp

5、erature (202) 温度 Relative humidity (655%) 相对湿度 Pressure (860 to 1060 mbars) 压力2.APPEARNCE, STYLE, AND DIMENSIONS外形,类型和尺寸2.1 Appearance 外形There shall be no defects that affect the serviceability of the product.外形必须无缺陷才不影响产品适用性2.2 Style and Dimensions类型和尺寸 Shall conform to the assembly drawings.符合装配图3

6、.TYPE OF ACTUATION 动作类型Tactile feedback 轻触返回4.CONTACT ARRANGEMENT 1 poles 1 throws 接触形式 1接点1回路(Details of contact arrangement are given in the assembly drawings.)细接点形式在装配图中5.MAXIMUM RATINGS DC 12 V 50 mA 最大额定值APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECT

7、SZ.DOC1/10ZONESYMBDATE APPDCHKDDSGDTACTING SWITCH SPECIFICATION6.PERFORMANCE性能6.1 Electrical电气Item项目Test Condition测试条件Requirements要求6.1.1.Contact Resistance接触电阻Applying astatic load twice the actuating force to the center of the stem,measurements shall be made with a 1 kHz small-current contact resi

8、stance meter.用两倍的动作力作静负载施加于按钮的中心,并用1千赫小电流接触电阻仪测量100 m ohm max.6.1.2.Insulation Resistance绝缘电阻Measurements shall be made following application of DC100V potintial across terminals and across terminals and frame for one minute.在端子与端子之间,端子与外壳之间施加DC100V,一分钟100 M ohm min.6.1.3.Dielectric witstanding volt

9、age电气耐压AC250V(50Hz or60Hz) shall be applied across terminals and across terminals and frame for one minute. 在端子与端子之间,端子与外壳之间施加AC250V(50HZ-60HZ)There shall be no breakdown.没有击穿6.1.4.Bounce抖动Lightly striking the center of the stem at a rate encountered in normal use (3 to 4 operations per sec.),Bounce

10、 shall be tested at “ON”and “OFF”. 在正常使用中(以每秒3-4次周期)轻轻地在手柄中心加力,在通与断瞬间测试抖动 5 m sec max.APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC2/10ZONESYMBDATE APPDCHKDDSGDTACTING SWITCH SPECIFICATION6.2Mechanical机械特性Item项目Test Condition 试验条件Requirements 规 格6.

11、2.1.Actuating Force动作力Placing the switch such that the direction of switch operation is vertical and then gradually increasing the load applied to the center of the stem, the maximum load required for the stem to come to a stop shall be measured.开关的动作方向为垂直放置开关向推柄中心逐渐地增加负荷直到推柄停止时所测量的最大负荷160 30 gf 250

12、 50 gf6.2.2.Travel行程Placing the switch such that the direction of switch operation is vertical and then applying a static load twice the actuating force to the center of the stem,the travel distance for the stem to come to a stop shall be measured. 开关的动作方向为垂直放置开关,并以双倍动作力的静负荷作用推柄中心,测量推柄从开始到停止的行程距离 0.

13、20 0.1mm6.2.3.Return Force返回力The sample switch is installed such that the direction of switch operation is vertical and,upon depression of the stem in its center the whole travel distance ,the force of the stem to return to its free position shall be measured. 开关的动作方向为垂直放置开关,在已有行程的推柄中心向上减小压力,推柄回到自由位

14、置时所测量到的力 45 gf min6.2.4.Stop Strength静止强度Placing the switch such that the direction of switch operation is vertical,a static load of 3 kgf shall be applied in the direction of stem operation for a period of 60 seconds. 开关的动作方向为垂直放置开关,在推柄动作方向施加3KG的静负荷,60秒时间There shall be no sign of damage mechanicall

15、y and electrically.无机械的和电气的损伤迹象6.2.5.Stem Strength推柄的强度Placing the switch such that the direction of switch operation is vertical, the maximum force to withstand a pull applied oppsite to the direction of stem operation shall be measured. 开关的动作方向为垂直放置开关,从推柄动作方向反方向施加拉力所测量到的最大承受力 3 kgfAPPDCHKDDSGDPART

16、 NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC3/10ZONESYMBDATEAPPDCHKDTACTING SWITCH SPECIFICATION6.3Environmental环境Item项目Test Condition测试条件Requirements要求6.3.1.Resistance to Low Temperatures耐低温Following the test set forth below the sample shall be left in normal te

17、mperature and humidity conditions for one hour before measurements are made:样品按下列条件进行耐低温试验,测试前在正常温度和湿度条件下放置1小时(1) Temperature: -302 温 度(2) Time: 96 hours 时 间(3) Water drops shall be removed. 擦除水珠Item 6.1Item 6. 2.1Item 6.2.26.3.2.Heat Resistance耐热Following the test set forth below the sample shall b

18、e left in normal temperature and humidity conditions for one hour before measurements are made: 样品按下列条件进行耐热试验,测试前在正常温度和湿度条件下放置1小时(1)Temperature: 802 温 度(2) Time: 96 hours 时 间Item 6.1Item 6. 2.1Item 6.2.26.3.3.Moisture Resistance耐潮湿Following the test set forth below the sample shall be left in normal

19、 temperature and humidity conditions for one hour before measurements are made: 样品按下列条件进行耐潮湿试验,测试前在正常温度和湿度条件下放置1小时(1) Temperature: 602 温度(2) Relative humidity: 90 to 95% 相对湿度(3) Time: 96 hours 时 间(4) Water drops shall be removed. 擦除水珠Contact resistance:500 m ohm max接触电阻Insulation resistance 10 M ohm

20、 min. 绝缘电阻Item 6.1.3Item 6.2.1Item 6.2.2APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC4/10ZONESYMBDATE APPDCHKDDSGDTACTING SWITCH SPECIFICATION6.4Endurance耐久性Item项目Test Condition测试条件Requirements要求6.4.1.Operating Life动作寿命Measurements shall be made fo

21、llowing the test set forth below:按下列条件进行寿命试验(1)DC 5V 5mA resistive load. DC 5V 5mA 阻性负载(2)Rate of operation:2 to 3 operations per second 动作频率:2-3次/每秒(3)Depression: 180 gf 减压力(4)Cycles of operation: 10104 cycles 动作次数: 10104次Contact resistance: 1 max. 接触电阻Insulation resistance : 10 M ohm min. 绝缘电阻Actu

22、ating force: 动作力+ 30 %or- 30%of initial force. 30%初始动作力Item 6.1.3tem 6. 2.26.4.2.VibrationResistance耐振动Measurements shall be made following the test set forth below: 按下列条件进行抗振动试验(1)Range of oscillation:10 to 55Hz 频率范围(2)Amplitude,pk-to-pk:1.5 mm 振幅: 峰-峰1.5mm(3)Cycle of sweep: 10-55-10Hz in one minut

23、e,approx.扫描周期: 10-55-10Hz约一分钟内(4)Mode of sweep :Logarithmically sweep or uniform sweep. 扫描方式:对数扫描式恒定扫描(5) Direction of oscillation: 振动方向Three mutually perpendicular directions,including the directionof stem travel. 3个相互垂直方向,包括推柄行程方向(6) Duration of testing: 持续时间2 hours each ,for a total of 6hours.每方向

24、2小时.共6小时Item 6.1Item 6.2.1Item 6.2.26.4.3.Impact ShockResistance抗冲击Measurements shall be made following the test set forth below: 按下列条件进行冲击试验(1)Acceleration:80g 加速度(2)Cycles of test :3 cycles each in 6directions, for a total of 18cycles 试验次数:每个方向3次,6个方向共18次 Item 6.1Item 6.2.1Item 6.2.2APPDCHKDDSGDPA

25、RT NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC5/10ZONESYMBDATEAPPDCHKDDSGDTACTING SWITCH SPECIFICATION7. Environmental Endurance 环境耐久性 Item项目Test Condition测试条件Requirements要求7.1.High Temperature Cycling高温循环Foeeowing ten cycles of high temperature test .Saupee shal

26、l be Place in Normae temperature and humidity Conditious for one hour before measurements are made. During this test, water drops shall be removed.样品按下列条件进行高低温循环试验,测试前在正常温度和温度条件下放置1小时,除去水珠(1) Temperature(温度)：-3080(2) Cycling(周期)：Ten cycles (10个周期)Item 6.1Item 6. 2.1Item 6.2.27.2Moisture Resistance耐潮

27、湿Following the test set forth below the sample shall be left in normal temperature and humidity conditions for one hour before measurements are made: 样品按下列条件进行耐潮湿试验,测试前在正常温度和湿度条件下放置1小时(1) Temperature: 852 温度(2)Relative humidity: 80 to 85% 相对湿度(3) Time: 500 hours 时 间(3) Water drops shall be removed.

28、擦除水珠Contact resistance:50 m ohm max接触电阻Insulation resistance 10 M ohm min. 绝缘电阻Item 6.1.3Item 6.2.1Item 6.2.27.3Terminae environment deposited Test端子放置实验Sample following the test below both condition In the constant temperature testing box it is deposited,than Surface of terminal dont serious oxidat

29、ion样品按下列条件在恒温箱中进行放置试验，端子应无严重氧化(1) Temperature: 605 温 度: 605(2) Time: 1200 hours 时 间 APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC6/10ZONESYMBDATEAPPDCHKDDSGDTACTING SWITCH SPECIFICATION8.Use Endurance 使用耐久性Item项目Test Condition测试条件Requirements要求8.1S

30、olderability焊接性Oven Temperature:2355，Time: 5S1S锡炉温度：2355 时间:5秒1秒 Tin Area:90焊接面积90以上8.2patience high temperature焊接耐热性Preheat: Temperature on the copper foil surface should reach 180, 20.3 minutes afterThe P.W.B entered into the soldering equipment预热：在P.W.B(印刷线路板)进入焊接设备后，20.3分钟内铜箔表面要达到180Soldering he

31、at: Temperature on the copper foil surface should reach the peak temperature of260 within 5 seconds after the P.B.W entered into soldering heat zone.焊接温度： 在P.W.B(印刷线路板)进入焊接温区5秒内，铜箔表面达到峰值温度260表面无起泡,变型Surface of plastics dont frothed And formedAPPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研

32、發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC7/10ZONESYMBDATEAPPDCHKDDSGD工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10 TACTING SWITCH SPECIFICATION9. Other precautions其他注意事项(1) Following the soldering process,do not try to clean the switch with a solvent or the like.进行焊接过程中，不可以用溶剂或类似品清洗开关(2) Safe

33、guard the switch assembly against flux penetration from its topside.防止助焊剂从开关的顶端渗入(3) Please have the products keep in close status and the storage time is 90 days guaranty after delivering the goods at most.交货后保证开关处于封密状态并库存时间90天以上APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.1

34、1.10DOCUMENT NO:SPECTSZ.DOC8/10ZONESYMBDATE APPDCHKDDSGDSLIDE SWITCH SPECIFICATION10. GENERAL 通用10.1 PACKING MATERIAL 包装材料ITEM SUBSTANCECARTON BOX 卡通箱CORRUGATED PAPER 瓦楞纸PACKING CTN 包装盒CORRUGATED PAPER 瓦楞纸PLASTIC BAG 塑料袋NORMAL PLASTIC 普通塑料10.2 PACKING UNIT 包装单位8.3.1 The capacity of packing ctn. 包装盒容

35、量Every carton box contains 10 packing ctn at most. 每个外箱内最多包括10个包装盒With a gross weight of 5kg around. 约5KG毛重左右8.3.2 Every packing carton contains 10k pcs goods at most. 每个包装盒内包括10KPCS产品With a net weight of500g around. 约净重500g左右10.4 Every plastic bag contains 1000 pcs goods at most with a net weight o

36、f 50 g. 每个塑料袋容纳1000PCS产品约净重50克Pulling-out direction10.5 THE SHAPE AND DIMENSION OF PACKING CARTON. 包装盒的外型及尺寸 APPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC9/10ZONESYMBDATE APPDCHKDDSGDTACTING SWITCH SPECIFICATIONITEM项目COMPONETS部 件MATERIAL ARTICLE 材 料SPECIFICATION 规 格1TERMINALTIN PHOSPHORBRONZE QSn6.5-01PLATE LAYERCYANIDE SILVER-PLATINGSILVER2FRAMELCPE130i3CONTACTAG-SUS301Ag=0.5u4HOUSINGSUS3045STEMLCPE130iAPPDCHKDDSGDPART NO:工 程 部赵 高 杰05.11.10研 發 部吴 公 元05.11.10研 發 部周 成 艮05.11.10DOCUMENT NO:SPECTSZ.DOC10/10ZONESYMBDATE APPDCHKDDSGD东莞市振鑫电子有限公司