焊接工艺评定(共18页).doc

《焊接工艺评定(共18页).doc》由会员分享，可在线阅读，更多相关《焊接工艺评定(共18页).doc（18页珍藏版）》请在得力文库 - 分享文档赚钱的网站上搜索。

1、精选优质文档-倾情为你奉上（委托检验）此仅为焊接工艺评定报告。一个完整的报告应是焊接工艺WPS和其对应的工艺评定。因此请更改封面为“阀门密封面堆焊工艺及评定”；并在报告中加上此评定报告所对应的焊接工艺（WPS）。 使其成为一个完整文件。(Entrusted inspection)检 验 报 告（副本）The report of inspection (copy)报告编号code： DCHP0001 委托单位：Entrusting unit: 成都迪川科技发展有限公司 Chengdu Dichuan technology development Co.Ltd 样品名称：sample name：

2、阀门密封面堆焊试样 The valve surfacing welding sealing surface samples 项目名称：project name： 阀门密封面堆焊工艺评定检验The surfacing procedure qualification inspection of valve sealingsurface 报告日期：report date： 2011年6月 四川省特种设备检验研究院The special equipment inspection institute of Sichuan province四川 成都Sichuan，Chengdu说 明 Instructi

3、ons一、 本检验报告仅对送检样品负责。The inspection report is just responsible for inspection sample二、 本检验报告涂改、增删无效，未加盖检验单位印章无效。The inspection report is invalid, automatically alter, not the inspection unit seal is invalid三、 送检单位若对本检测报告有异议，可在收到报告之日起十五日内，提出复核申请，逾期不受理。If those units this inspection report any, availab

4、le to receive the report within 15 days of the date of application for review, and puts forward is not accepted 四、 本检验报告及本检验机构名称未经许可不得用于产品标签、广告、商品传单等。The name of the inspection report and inspection agencies without permission shall not be used for product labels, advertising, advertising products a

5、nd assessment, etc. 五、本检验报告一式两份，正本交送检单位，副本由检验机构存档。The inspection report is induplicate，the original is sent to those units，the inspection authority keep the copy .四川省特种设备检验研究院。The special equipment inspection institute of Sichuan province地 址Address：成都市东风路二段北二巷4号Chengdu Dongfeng road two sections of

6、north2lane4邮政编码Postal code ： 电话Telephone：028- 四川省特种设备检验研究 The special equipment inspection institute of Sichuan province 专心-专注-专业检 验 报 告（副本） The report of inspection(copy) 报告编号Report code：DCHP0001 委托单位Entrusting unit：成都迪川科技发展有限公 Chengdu Dichuan Technology Development Co., Ltd用户地址Customer address: 四川

7、成都 Sichuan Chengdu 联系电话:Telephone: 样品名称Sample name:堆焊试板 Welding test plate试样编号Sample code: DC04样品来源Sample source： 抽查 用户送样介 质Medium： /规 格Specification : / 材 质Material：ASTM A350 LF2（基Base material）+ STELLITE6（堆overlay）公称工作压力nominal operating temperature：/ 设计温度design temperature：/检验依据 Inspection standa

8、rds：ASTM A388、ASTM E-165、 API 6D、ASTM E92、NACE MR 0175/ISO15156、ASTM E415、AP16D、ASME IX、GB/T 226-1991GB/T 13298-1991、 ASTM A370检验结果与结论The results and conclusions：符合委托conform to entrust。注：1.本检验报告仅对检验样品负责。2.本检验报告涂改、增删无效，未加盖检验单位印章无效。3.本检验报告复印件无效。notes：1. The inspection report is just responsible for in

9、spection sample2. The inspection report is invalid, automatically alter, not the inspection unit seal is invalid3. The inspection report is invalid for copy检 验Inspected by：审 核Reviewed by：签 发Signature： 日 期Date：技术负责人Technical leader: 检验专用章Special stamp for inspection:四川省特种设备检验研究The special equipment i

10、nspection institute of Sichuan province委托检验项目表Entrusted inspection items form试样编号Sample Code：DC04 报告编号 Report Code：DCHP0002序号Serial number检验、检测项目Inspection and testing items依据标准Standard结 论Conclusion备 注Notes1超声波检测Ultrasonic testing ASTM A388合格Qualified2渗透检测Penetrant testing ASTM E-165合格Qualified3硬度检测

11、Hardness testing API 6D；ASTM E92；NACE MR 0175/ISO15156符合委托是符合委托，还是标准要求，还是川东北项目的要求？请检查、修改！Conform to entrust4化学分析Chemical analysis ASTM E415；AP16D；ASME IX；NACE MR 0175/ISO15156符合委托Conform to entrust5金相检测Metallographic analysis GB/T 226-1991GB/T 13298-1991符合委托Conform to entrust6机械性能试验Mechanical testin

12、g ASTM A370符合委托Conform to entrust以下空白The following is blank检验Inspected by： 日期Date审核Reviewed by： 日期Date:Welding procedure specification（WPS）焊接工艺规程WPA NO： DCHP0001-1REV NO:K1DATE:2011.6.20Name of project项目名称：钨极氩弧焊ASTM A350 LF2+ STELLITE6/ ASTM A350 LF2+ STELLITE6 GTAM OverlayName of part零件名称：评定试样 samp

13、les of assessmentWelding process(es)焊接方法：GTAMTYPE(s)型式： Manual手动 Semi- auto半自动 Auto自动BASE METALS 母材（ DCR-51）Specification. Type and Grad 规格型号等级为: ASTM A350 LF2Thickness Ranger 厚度范围Base Metal母材 Groove 坡口焊缝:300x300x38mmWELD JIONT 焊接接头形式（ DCR-49）FILLER METALS 填充金属（ DCR-52）Spec. No.（SFA）规格编号 :SFA A5.21A

14、SW No.等级No.ERCoCr-A GB No.ERCoCr-ASize of filler Metal 填充金属尺寸3.2mmWeld Meter焊缝金属Thickness Range of Filler metals 熔敷金属厚度：3.2t5POSITION 焊接位置（ DCR-53）Position of Groove 坡口的位置(平焊/F)Welding Progression （Up、Down）焊接方向（向上、向下）不适用N/APOSTWELD HEAT TREATMENT 焊后热处理（ DCR-55）Temperature温度 63514Times 保温时间1h/in.出炉空气

15、中冷却PREHEAT 预热（ DCR-54）Preheat Temp 预热温度 25050Interpass Temp 层间温度Max 300Prcheat Maintance 预热保持方式 火焰或电阻加热器Burner with Gas or Electric Resisitance HeaterTECHNIQUE技术（ DCR-56）String or Weave Bead 直行或摆弧：摆弧/ Weave BeadSingle or Multiple pass单道焊或多道焊：多道焊/Multiple passWELDING PARAMETERS焊接参数 (DCR-57)层数Pass NO焊

16、接方法Process焊材Electrode焊材直径（size）接线方式 Connection Type电流大小（A）currentVolts电压（V）喷嘴直径 nozzle diameter氩气流量 (L/min)Argon gas flow焊接速度（cm/min） Welding speed 1GTAWERCoCr-A3.2mm直流正接1201802030613mm8106122GTAWERCoCr-A3.2mm直流正接1201802030613mm810612WORK REQUESTION操作要求：1. welding surface need to machining, roughnes

17、s can be up to 6.3，and keep clean . Rust ，oil and etc are not allowed .If the surface of work piece have stomata, crack, porosity, shrinkage defects ，the welding can be done after trimming repairing welding焊件表面需以机械加工，粗糙度6.3以上即可，并保持清洁，不得有铁锈、油污等。若工件表面有气孔、裂纹、疏松、缩孔等缺陷时，应先补焊修整后，才能进行堆焊。2. Each layer of we

18、lding scraps must be c leaned up and the face of surfacing welding must be cleaned up, and 100% for VT, PT and UT inspection.每层的焊接残渣必须清理干净，焊接堆焊面必须清理干净，并且100%进行VT、PT和UT检验 PREPARED BY编制REVIEWED BY审核APPROVED BY批准DATE 日期DATE 日期DATE 日期Welding Procedure Qualification Records （PQR）焊接工艺评定记录（ DCR-57）PQR NO：D

19、CHP0001-2REV NO:K1DATE:2011.6.20Name of project项目名称：钨极氩弧焊ASTM A350 LF2+ STELLITE6/ ASTM A350 LF2+ STELLITE6 GTAM OverlayName of part零件名称：评定试样 samples of assessmentWPS NO/Rev. No：焊接程序编号/修订号： DCHP0001-1K01Welding process(es)焊接方法： GTAMTYPE(s)型式： Manual手动 Semi- auto半自动 Auto自动BASE METALS 母材（ DCR-51 ）Spec

20、ification Type and Grad 规格型号等级为: ASTM A350 LF2Thickness Ranger 厚度范围Base Metal母材 Groove 坡口焊缝:300x300x38mmWELD JOINT 焊接接头形式（ DCR-49）FILLER METALS 填充金属（ DCR-52）Spec. No.（SFA）规格编号SFA A5.21ASW No.等级 ERCoCr-A GB No. ERCoCr-ASize of filler Metal 填充金属尺寸3.2mmWeld Metal焊缝金属Thickness Range of Filler metals 熔敷金

21、属厚度：4 Test Report No检验报告编号：DC-HJ-ZL-01POSITION 焊接位置（ DCR-53）Position of Groove 坡口的位置平焊1GWelding Progression （Up、Down）焊接方向（向上、向下）不适用N/APOSTWELD HEAT TREATMENT 焊后热处理（ DCR-55）Temperature温度 63514Times 保温时间1.5h/in.出炉空气中冷却PREHEAT 预热（ DCR-54）Preheat Temp 预热温度 25050Interposes Temp 层间温度Max 300Preheat Maintai

22、ned 预热保持方式 火焰或电阻加热器Burner with Gas or Electric Resistance HeaterTECHNIQUE技术（ DCR-56）String or Weave Bead 直行或摆弧：摆弧/ Weave BeadSingle or Multiple pass单道焊或多道焊：多道焊/Multiple pass焊接参数 welding parameter层数Pass NO焊接方法Process焊材Electrode焊材直径（size）接线方式 Connection TypeAmps电流（A）Volts电压（V）喷嘴直径 nozzle diameter氩气流量

23、(L/min) Argon gas flow焊接速度 Welding speed （cm/min）1GTAWERCoCr-A3.2mm直流正接130256mm9102GTAWERCoCr-A3.2mm直流正接130256mm910Guide Bend Test 导向弯曲试验 Report No试验报告编号; DCHP0008Specimen NO 试样号Type of Bend 弯曲类型Results 结果Remarks 目测结果CDCW01侧弯 Side Bend合格 Accepted无可见裂纹 No defect was observedCDCW02侧弯 Side Bend合格 Accep

24、ted无可见裂纹 No defect was observedCDCW03侧弯 Side Bend合格 Accepted无可见裂纹 No defect was observedCDCW04侧弯 Side Bend合格 Accepted无可见裂纹 No defect was observedHardness Test 硬度试验 Report No试验报告编号; DCHP0005Specimen NO 试样号Test Location 试验位置Hardness 硬度（HV10）Conclusion 结论DC04堆焊层surfacing layer427合格 Accepted热影响区heat aff

25、ected zone243合格 Accepted母材base metal242合格 AcceptedDeposit Analysis 堆焊层化学成分试验 Report No试验报告编号; DCHP0009材料牌号CMnSiPCrSWFeNiMoCoERCoCr-A1.20.21.20.00829.80.0094.52.42.20.01余量Rest ofTENSILE AND IMPACT TEST RECORD 理化试验报告 Report No试验报告编号; DCHP0007b/Mpas/MpaAs (%)(%)冲击试验AK/J48549025026522233032规定值 Specifica

26、tion-18-4616/20冲击试验的规定值和实测值均应有单个值和平均值。请修改。Visual Test 目视检验：No Visible Crackles and Air Holes. OK无可见裂纹和气孔.合格NDT Results 无损探伤结果：PT；UT OK液体渗透探伤合格；超声波探伤合格Test Report No 检验报告编号：DCHP0004、DCHP0003Macrograph Examination of Welding Joint焊接接头宏观检验：Overlay and Base Metal have good fusing，and no visible weld def

27、ects堆焊层与母材熔合完好，未见明显焊接缺陷： Test Report No 检验报告编号：DCHP0006Welders Name 焊工姓名：刘效东/liuxiaodong Welders Stamp No.焊工鉴号：TS6JCTU02838Tests Conducted by 试验支持人：干兵Laboratory Test Record No.试验记录编号：DCHP0001-3Test Place 试验地点：四川省特种设备检验研究院。The special equipment inspection institute of Sichuan provinceWe certify that

28、the statements in this record are correct and that the test welds were prepared，welded and tested in accordance with the requirements of：ASTM A388、ASTM E-165、 API 6D、ASTM E92、NACE MR 0175/ISO15156、ASTM E415、AP16D、ASME IX、GB/T 226-1991、GB/T 13298-1991、 ASTM A370 Code,兹证明以上所列各项记录无误，并且所有试片之准备、焊接以及试验均完全

29、符合ASTM A388、ASTM E-165、 API 6D、ASTM E92、NACE MR 0175/ISO15156、ASTM E415、AP16D、ASME IX、GB/T 226-1991、GB/T 13298-1991、 ASTM A370 规范的要求。PREPARED BY编制REVIEWED BY审核APPROVED BY批准DATE 日期DATE 日期DATE 日期焊接质量记录WELDING QUALITY RECORD程序文件号DCR-50Customer用户:成都迪川科技发展有限公司Chengdu Dichuan Technology Development Co., L

30、td Record记录号;DCHP0001-3Project No 项目号Welding procedure qualification焊接工艺评定Part Name产品型号名称Welding test plate焊接试板Drawing No零件名称图号DCCDBHP04Part No 零件流水号DC04Base metal No母材牌号ASTM A350 LF2WPS No焊接工艺规程编号DCHP0001-1Type of welding施焊方式Manual手工 Semi- auto半自动 Auto自动Machinery No.焊机编号DCSB-2011-04Solder Type No.焊

31、机型号TIG-500Welding description焊接描述;Preheat预热Base metal 母材Preheating Fashion预热方式Temperature温度（）Preservation time保温时间（h）局部 整体3001h层数Pass NO焊接方法Process焊材Electrode焊材直径（size）接线方式Amps电流（A）Volts电压（V）喷嘴直径 Nozzle diameter氩气流量 Argon gas flow (L/min)焊接速度 Welding speed （cm/min）1GTAWERCoCr-A3.2mm直流正接130256mm9102G

32、TAWERCoCr-A3.2mm直流正接130256mm910PWHT 焊后热处理Heat Treatment Fashion热处理方式Temperature/温度Preservation time/h保温时间局部 整体6351Visual目视检查; （No visible crackles and air holes， OK） 无可见裂纹和气孔，合格不合格，描述Thickness of overlay堆焊层厚度:4mmInspector 检验员; Worker；Date日期： Date日期：超声波检测报告The report of UT 报告编号 Report Code： DCHP0003委

33、托单位Entrusting：成都迪川科技发展有限公司Chengdu Dichuan Technology Development Co., Ltd零件名称Part name焊接试板Welding test plate试样编号Sample codeDC04材料MaterialASTM A350 LF2+ STELLITE6焊接方法Welding method钨极氩弧焊GTAM热处理状况Heat treatment condition635（1H）检测标准StandardASTM A388探伤表面粗糙度Roughness of examination1.6检测比例Detection ratio见下

34、图 See below检测部位Testing site见下图See below 检测条件及工艺参数Detection conditions and Process parameters仪器型号Instrument modelPXUT-3300探头型号Probe models 2.5P 20Z耦合剂Coupling agent机油 Oil 表面补偿Surface compensation 4Db检测方法Detection method 纵波反射法 Wave reflection method 试块型号Try piece of model CS-检测灵敏度Detection sensitivity

35、 3.2扫查方式Scanning mode 全方位 All-round 检 测 部 位 及 缺 陷 情 况Inspection site and defects conditions检测部位编号Inspection site number检测尺寸 Inspection size（mm）缺陷编号Defects number缺陷埋藏深度（mm）Defects buried Hidden depth（mm）缺陷尺寸(mm)Defects size（mm）缺陷高度(mm)Defects height（mm）缺陷类型Defect type缺陷波反射区域Defects wave Reflection ar

36、ea评定级别Assessment level备注Notes探伤面Test surface见下图See below0000000此部分请找专业人员填写。全填 0 不正确！/检测部位图： The figure of inspection site:300300区域为UT检测区域检测日期Inspection Date:检验人员/技术资格/时间Inspection personnel/technical qualifications/time: 审核人员/技术资格/时间The review personnel/technical qualifications/time: 渗透检测报告The repor

37、t of PT 报告编号Report Code： DCHP0004委托单位Entrusting：成都迪川科技发展有限公司Chengdu Dichuan Technology Development Co., Ltd工件名称Workpiece name ：焊接试板Welding test plate 试样编号Sample codeDC04工件规格Workpiece specification300mm*300mm工件材质Workpiece materialASTM A350 LF2+ STELLITE6坡口型式Groove type/焊接方法Welding method手工 manual 热处理

38、状况Heat treatment condition/检测比例Detection ratio见下图 See below 预清洗方法precleaning method溶剂清洗 Solvent cleaner 观察方法Observation method日光下目视 Sunlight visual 后清洗方法post cleaning method擦洗Scrubbing原检测标准Original inspection standard/原检测比例Original detection ratio/检测标准Inspection standardASTM E-165验收等级Acceptable leve

39、lISO10423 PSL（3G）乳化剂施加方式Method of adding emulsifier-水压水温Water pressure、temperature-去除方法Removal method擦除 Erase 干燥方法Dry method自然干燥 Natural drying 检测条件及工艺参数Detection conditions and Process parameters渗透检测方法Method of PT溶剂去除型着色法 Coloring 渗 透 剂Penetrating agentHG-3显 像 剂Imaging agentHG-3乳 化 剂Emulsifying age

40、nt-清 洗 Cleaning agentHG-3渗透剂施加方式Method of adding penetrating agent喷 Spray乳化时间Emulsification time-Min显像剂施加方式The method of adding imaging agent喷 Spray渗透温度Penetration temperature温度Temperature：26渗透时间Penetration time10min干燥温度dry temperature温度Temperature ：26 干燥时间Dry time5min显像时间Imaging time 7min灵敏度校验试块Sen

41、sitivity of calibration coupon镀铬试块Chrome plated test blocks 检测部位及缺陷情况Inspection site and defects conditions检测部位编号Inspection site code检测尺寸（mm）Inspection size缺陷编号Defects code缺陷痕迹尺寸（mm）Defects trace size缺陷类型Defects type 评定级别Assessment level备 注Notes探伤面Test surface见下图See below0000此部分请找专业人员填写。全填 0 不正确！/检测部位图： The figure of inspection site:300300方形区域为PT检测区域300 x 300 Square area for PT testing area检测日期inspection date:检验人员/技术资格/时间Inspection personnel/technical qualifications/time: 审核人员/技术资格/时间The review personnel/technical qualifications/time: 硬度检测报告 The report of hardness tes